Boom-type roadheader cutting rock in an underground tunnel with dust and water mist

Industrial radar / FMCW heavy equipment anti-collision

77 GHzEquipment Safety Radar

Part number TR3264

Close-range protection for roadheaders, shield backup systems, mining trucks, port equipment and overhead cranes — radial distance, relative velocity and azimuth for people and large obstacles, held through dust, water mist, shotcrete and condensation.

77 GHzFMCW carrier
0.2–40 mVehicle & obstacle range
±60°Azimuth field of view
≤100 msUpdate period

Anti-collision that keeps working when the face is lost in dust.

Cameras and LiDAR fail first where machines actually work: cutting faces, shotcrete spray, high-humidity headings and wash-down areas. TR3264 reads the scene with a frequency-modulated continuous wave through a spherical lens, so rock powder and mud slide off instead of blocking the beam.

TR3264 heavy equipment safety radar with a fan-shaped detection beam
40mVehicles & large obstacles
15mPersonnel detection
±0.1mRadial accuracy
±0.1m/sVelocity accuracy

One sealed block, mounted where the machine is blind.

No flying tail cable, a rigid two-lug flange and a round sealed connector on the rear face. Each drawing below carries the parameter it governs.

The spherical lens projects the chirp as a wide fan ahead of the machine, covering the swing arc of a boom or the approach path of a haul truck. Objects inside that fan are reported with distance and azimuth, so an operator knows not only that something is there but where.

BeamAzimuth ±60°, elevation ±15°; personnel to 15 m, vehicles and large obstacles to 40 m.
TR3264 front view drawing
TR3264 side view drawing

The housing is a machined stainless block with two mounting lugs, fixed on a rigid bracket with anti-loosening fasteners so cutting vibration cannot drift the axis. There is no cable to whip or abrade: the unit terminates at its own connector.

ConstructionStainless steel housing with wear-resistant spherical lens, IP67; −40 to +85 °C; vibration and shock referenced to IEC 60068-2-6 and GB/T 2423.10.

Four screws hold the rear cover over a sealed multi-pin connector, which drops straight into the machine harness. Distance, relative velocity and azimuth leave on the vehicle bus, with static and dynamic targets classified on board so alarms do not trip on a parked loader.

OutputCAN 2.0B at 250 or 500 kbit/s; 12–36 V DC supply, <4.0 W design target; route the bus away from cutting-motor and inverter cables.
TR3264 rear view drawing

Four working fronts where people and machines share the same metres.

Tunnelling, lifting and haulage all put an operator and a pedestrian inside one another's blind spot. The same sensor watches the cutting arc, the segment lift, the hook path and the roadway.

Boom-type roadheader at a tunnel face with workers nearby and dust in the air
Boom-type roadheaders

Personnel kept out of the cutting arc

Alert the crew and the operator when a person or a large rock enters the swing area around the cutting head, before the boom turns.

Shield machine backup gantry lifting a concrete segment in a tunnel
Shield & TBM backup

Clearance for gantries and segment lifts

Watch the backup gantry walkway and the segment hoisting zone, where a swinging ring is hard to see from the operator cab.

Overhead travelling crane lifting a steel bundle across a workshop floor with workers below
Overhead & bridge cranes

Zones under a moving hook

Detect people and stacked loads in the travel path of the bridge and trolley, and alarm before the hook reaches the crossing.

Rubber-tyred load-haul-dump vehicle in a non-coal mine roadway
Mining rail-less vehicles

Blind-zone alerting in the roadway

Front and rear warning for rubber-tyred loaders and haul trucks in non-coal roadways, where dust cuts sight distance to a few metres.

Engineering data for machine integration.

Microwave, electrical, environmental and mechanical parameters are consolidated here for bracket design, harness routing and control-logic mapping.

Frequency / modulation
77 GHz millimetre wave / FMCW; complies with radio transmission type approval
Positioning
Alerting personnel, vehicles and large obstacles around tunnelling, mining and lifting equipment
Communication
CAN 2.0B, 250 / 500 kbit/s
Supply / consumption
12–36 V DC / <4.0 W design target
Detection range
Personnel 0.2–15 m; vehicles and large obstacles 0.2–40 m
Measurement accuracy
±0.1 m radial, open field, centre of field of view
Velocity
Radial relative −20 to +20 m/s; accuracy ±0.1 m/s
Field of view
Azimuth −60° to +60°; elevation −15° to +15°
Update rate
Measurement period ≤100 ms, multi-target with static / dynamic classification
Operating temperature
−40 to +85°C
Mechanical environment
Referenced to IEC 60068-2-6 and GB/T 2423.10 vibration and shock standards
Materials
Stainless steel housing, wear-resistant spherical lens
Protection / connection
IP67; sealed multi-pin connector on the rear face, no tail cable
Mounting
Rigid bracket with anti-loosening fasteners; lens cleaned each shift; verify field of view against machine contours

Mount it before the machine starts cutting.

Share the machine contour, the blind zone to be covered and the bus layout, and we will return bracket geometry and warning-zone limits.

Discuss your application
Message Us